Defelsko Certified Coated Metal Plates & Certified Polystyrene Blocks

Only by Request

Clear
Part # N/A Category

Certified coated metal plates and polystyrene blocks are ideal for verifying the accuracy and operation of coating thickness gages and are an important component in fulfilling both ISO and in-house quality control requirements.

Many organizations require verification of gage accuracy at the test site each time a coating thickness gage is put into service and at frequent intervals during use. Ideal for this purpose, DeFelsko certified coating thickness standards have measured values traceable to a National Metrology Institution.

  • Used to verify the accuracy and operation of any Type 1 (mechanical) and Type 2 (electronic) magnetic, eddy-current or ultrasonic coating thickness gage
  • Ideal for use in the calibration lab, in the field or on the factory floor
  • Standards with steel or aluminum substrates consist of 4 plates mounted in a protective binder
  • Polystyrene thickness standards consist of 4 blocks supplied in a rugged acrylic storage box
  • Individually serialized for traceability to NIST or PTB – includes a Certificate of Calibration
  • Certified and labeled in both Metric and Imperial units
Zero Plates available for both Certified Coated Metal Plates and Certified Polystyrene Blocks.
Type

Certified Coated Metal Plates, Certified Polystyrene Blocks, Plastic Shims, Zero Plates

Model

A1, A2, A3, CS1, CS10, CS2, CS20, CS3, CS40, CS5, CS60, CSS, P1, P2, P3, P4, P5, P6, P7, P8, S1, S2, S3, S4, STDZALM, STDZALMM, STDZSTL, STDZSTLL, STDZSTLM

Certified Coated Metal Plates

Select the Standard that most closely matches the measuring range of your gage.
*PosiTector FXS probes with  a range of 0-1500 um (0-60 mils) and Serial Numbers <361485 should use the S1 Standard. ‍All certified standards are supplied with a Certificate of Calibration traceable to NIST or PTB.
Plate Diameter: 38 mm (1.5″) Measurement Diameter: 25 mm (1″)

Certified Polystyrene Blocks

Select the Standard that most closely matches the measuring range of your gage.
All certified standards are supplied with a Certificate of Calibration traceable to NIST or PTB.
P1-P7 Blocks: 38 x 70 mm (1.5″ x 2.75″)   P8 Blocks: 76 x 76 mm (3.0″ x 3.0″)

Plastic Shims

Certified Plastic Shims (foils) provide an economical alternative to coated metal plates. They have a reduced accuracy of ±2 µm (±0.08 mil). A coating thickness gage measures shim thickness when this shim is placed over a smooth metal surface (zero plate).

Non-Certified Plastic Shims (foils) provide a quick operational check of the instrument and they allow the user to perform practice measurements when placed over metal.

Alternatively, they can be placed over an uncoated metal substrate. They are not suitable for use with magnetic pull-off gages.

Shims overview:

  • Simulate a coating over a particular substrate material or shape. Gage performance can be conveniently verified on a regular basis as required by some international test methods
  • For use with all Type 2, electronic coating thickness gages
  • Protects the probe from damage or premature wear when placed over hot or abrasive surfaces
  • Can be placed on top of soft or tacky coating films to obtain thickness measurements without the gage probe depressing the coating film
  • Dimensions: 3 x 8 cm (1 x 3 inches)

Specifications & Ordering Guide

Certified Plastic Shims

  • Certified shims provide an economical alternative to Coated Metal Plates but have a reduced accuracy
  • Each shim is packaged in a protective sleeve
  • Certificate of Calibration showing traceability to PTB is included with each shim or set of shims
  • Certified and labeled in both Metric and Imperial units

Non-Certified Plastic Shims

  • Provide a quick operational check of the instrument by allowing the user to perform practice measurements
  • Can be used to protect the probe when measuring on tacky, rough or hot surfaces
  • Labeled in both Metric and Imperial units
Login to NOMO

NOMO Deals

Get the best offers in NDT products.